Reising firing pin breakage

ferndog1

UZI Talk Supporter
Feedback: 8 / 0 / 0
Joined
Mar 7, 2007
Messages
772
Location
South West PA
The most common failure on Model 50-55 Reising submachine guns is broken firing pins.

There are a lot of smart and skilled individuals in the class III community. The community needs one of these individuals to design and manufacture a Reising SMG firing pin that will last for at least a few thousand rounds.

Original steel firing pins are impossible to find; the only new manufacture pins available are those made of titanium. I cannot get one to last more than 500 rounds before the tip breaks off.

There have been some semi-successful advancements, like the inertia modification described in the link below. In my experience, the inertia modification works best with original steel firing pins, the titanium pins not so much.

The inertia firing pin thread (unfortunately, the photos are gone)


There is another individual on machinegunboards.com who was doing some experimenting I have pasted a link to his thread. On his last post, he had not yet been successful.

 

Galil#1

Well-known member
Feedback: 2 / 0 / 0
Joined
Jun 21, 2018
Messages
999
^^^ Amen! ^^^
Make The M50 Great Again!
Please make a high quality strong steel FP... can this be worth to make?
 

ferndog1

UZI Talk Supporter
Feedback: 8 / 0 / 0
Joined
Mar 7, 2007
Messages
772
Location
South West PA
A guy was working on a fix over on the Reising board at machinegunboards.com
Not sure if he is still experimenting.

I cannot get more than a few hundred rounds out of a firing pin.
 

Galil#1

Well-known member
Feedback: 2 / 0 / 0
Joined
Jun 21, 2018
Messages
999
^^^ Fudge, thank you FD1. ^^^ Would like to purchase several new well made ones myself too Sir.
 

r

Well-known member
Feedback: 5 / 0 / 0
Joined
Dec 28, 2002
Messages
720
Location
somewhere
maybe these pics were what you meant from the Cort article. I have a keystone pin which I could mic, then I mic'ed the side by side photos and extrapolated to make the proposed pin drawing and am currently attempting to get one made and then hardened
 

Attachments

  • 658061989_PXL_20250804_1340390572.jpg.b9886d247a7f6b8a5c5f47dc64c299fd.jpg
    658061989_PXL_20250804_1340390572.jpg.b9886d247a7f6b8a5c5f47dc64c299fd.jpg
    204.4 KB · Views: 9
  • PXL_20250726_002659469.thumb.jpg.20289860067e6ed049e5168f0eafeaee.jpg
    PXL_20250726_002659469.thumb.jpg.20289860067e6ed049e5168f0eafeaee.jpg
    132.3 KB · Views: 9
  • PXL_20250804_162118872.thumb.jpg.31a48545fc36c2f72ed334b72e148355.jpg
    PXL_20250804_162118872.thumb.jpg.31a48545fc36c2f72ed334b72e148355.jpg
    83.1 KB · Views: 7
  • firing pin protrusion 2.jpg
    firing pin protrusion 2.jpg
    76.6 KB · Views: 9
  • pin dimensions as measured.pdf
    557.9 KB · Views: 4

Strangeranger

Well-known member
Feedback: 1 / 0 / 0
Joined
Jul 4, 2019
Messages
364
Location
Ohio
I'm uncertain whether titanium is the correct metal for the pins. Personally I think I'd use 4140HT or 4340HT as was suggested in that thread but there are other applicable alloys out there

The real problem with the Keystone pin is that it is a flawed design. The shoulder just back of the tip creates a stress concentration and that is typically where pins break. Cort made two huge improvements over the stock and Keystone versions
He limited the firing pin protrusion. That eliminated one entire class of failures
He beveled the 90° shoulder back to 45° and later to 30°. That reduced the stress concentration and increased the mean time between failures.
He had decent results with 1144 ("Stressproof") so he was onto something. He had heat treating issues with S7 but at Rc55 it was far too brittle. We haven't heard from him in a while but the solution should be out there. I'd bet on his design machined out of 4340HT and hardened to something like Rc45
 

hacker

Well-known member
Feedback: 1 / 0 / 0
Joined
Jun 15, 2019
Messages
68
Location
Wisconsin
Since the original pins work with the inertia modification, why not copy them?
 
  • Like
Reactions: K2

Strangeranger

Well-known member
Feedback: 1 / 0 / 0
Joined
Jul 4, 2019
Messages
364
Location
Ohio
The original pins do not work 100%. They still fail. Additionally they are difficult to machine compared to a non-tapered pin. I'm only guessing here but I think that the reason behind the original design was that Eugene Reising was aware of the stress concentration issue and sought to avoid it with the full length taper.

There are three separate issues in play: the correct geometry for the pin, the correct alloy and the heat treatment. Cort's design appears to have solved the first by limiting the protrusion of the firing pin tip and reducing the stress concentration in the straight-walled design. He has come very close on the second (1144 is probably not quite as good in impact resistance as 4140/4340.) Getting exactly the correct alloy should largely define the heat treatment
 

Shattered

Well-known member
Feedback: 3 / 0 / 0
Joined
Oct 3, 2007
Messages
2,276
Location
North Coast
Following this and I've only broken my original pin, then again, I've owned this thing for close to 30 years and it never really worked. Bubba Naess got it running some years back and since then it's become a favorite. Of course now it's broken a pin, lost a chuck of the comp and finally broke the ejector. Getting it back on the road will be a bit tougher since Bubba retired but I can most likely get it done.
 

Galil#1

Well-known member
Feedback: 2 / 0 / 0
Joined
Jun 21, 2018
Messages
999
Anyone can recommend a real specialist type gunsmith for the Reising M50? Seen video and have the Wolff spring kit; however, looks real PITA all the springs etc. and would need 100% functioning afterwards etc. Thanks!
 

Strangeranger

Well-known member
Feedback: 1 / 0 / 0
Joined
Jul 4, 2019
Messages
364
Location
Ohio
Its really simple to install a spring kit except for the spring(s) for the end cap ratchet pawl(s). Just ignore those

When working with the tiny springs and plungers do everything inside a large dry cleaner's bag. You won't have to chase the ones that get away from you nearly as far
 

Strangeranger

Well-known member
Feedback: 1 / 0 / 0
Joined
Jul 4, 2019
Messages
364
Location
Ohio
Following this and I've only broken my original pin, then again, I've owned this thing for close to 30 years and it never really worked. Bubba Naess got it running some years back and since then it's become a favorite. Of course now it's broken a pin, lost a chuck of the comp and finally broke the ejector. Getting it back on the road will be a bit tougher since Bubba retired but I can most likely get it done.
You can get a replacement (and much more durable comp from https://bullcreekarms.com/store/reising-model-50-compensators-1/
 

skoda

UZI Talk Life Member
Feedback: 5 / 0 / 0
Joined
Mar 23, 2010
Messages
1,156
The original pins do not work 100%. They still fail. Additionally they are difficult to machine compared to a non-tapered pin. I'm only guessing here but I think that the reason behind the original design was that Eugene Reising was aware of the stress concentration issue and sought to avoid it with the full length taper.

There are three separate issues in play: the correct geometry for the pin, the correct alloy and the heat treatment. Cort's design appears to have solved the first by limiting the protrusion of the firing pin tip and reducing the stress concentration in the straight-walled design. He has come very close on the second (1144 is probably not quite as good in impact resistance as 4140/4340.) Getting exactly the correct alloy should largely define the heat treatment
I did this with a titanium pin when I had my Reising. After two breakages I took another and shortened it to the point where it would just barely fire the round and I also reprofiled the shoulder a little to reduce the stress riser and give the pin a little room to move around after hitting the primer. It helped quite a bit but it still eventually broke. Titanium is too soft for the job. It needs a good grade of steel with the proper heat treatment but those are tougher to machine. Good luck to all of you. Cool MGs but they have a lot of 'needs'.
 

Please Visit our Sister Sites Below

Sister Board - Sturmgewehr Sister Board - MachinegunBoards


Please consider becoming an UZI Talk Supporter
Top