Bolt sticking???

MitchWerbellsGhost87

Uzi Talk Life Member, MacExpert!
Feedback: 6 / 0 / 0
Joined
Dec 11, 2022
Messages
1,355
Location
USA
I recently obtained a demilled parts gun, Action Arms Model B carbine parts, assembled on a McKay receiver. Welded it up (actually used an Uzi weld jig for the first time ever) but the bolt seems to like to stick in the rearward position sometimes. I think it is binding on the top cover slightly, the top cover is a little tougher to snap closed than they typically are, and I suspect the bolt is possibly being squeezed between the top cover and blocking bar? It happens intermittently, especially when the bolt is pulled rearward with a bit more force, which means it’s likely to happen upon firing it. When I release the top cover on the stuck bolt, the bolt immediately releases and slaps forward freely.. so the cover fit is seemingly the culprit. Any easy fix for this before I start trimming, grinding and guessing???

I am admittedly not much of a welder, but this one came out OK. I hate welding cut up uzis, I have to be like Michelangelo with the dremel cutting discs to clean up and reshape the dirt ribs. It’s a little bit of a pain in the ass for an amateur like myself, but I’m satisfied with the results, I am also pretty confident the receiver is straight since I used the jig and everything seems to line up properly.. I feel like this could likely be remedied by making a small adjustment somewhere.. but maybe im wrong and the whole thing needs to be cut and rewelded (hopefully not the case).

IMG_6405.jpeg
IMG_6408.jpeg
IMG_6407.jpeg
IMG_6406.jpeg
 

Attachments

  • IMG_6406.jpeg
    IMG_6406.jpeg
    920.5 KB · Views: 5

AKarms

Well-known member
Feedback: 1 / 0 / 0
Joined
Feb 12, 2024
Messages
405
Location
New Hampshire
Bend the top cover outward in a press, (keep in mind still need to maintain proper clearance so bolt will still feed and function properly) more towards the rear, and/or take a little material off of the rear of the topcover (the flat) where it locks in to give it a little clearance. This is the quick and dirty way to get some clearance. Or, if you have a belt sander, take a few thou off top of bolt. Small adjustments. Seems like you just need a hair or 2
 
Last edited:

AKarms

Well-known member
Feedback: 1 / 0 / 0
Joined
Feb 12, 2024
Messages
405
Location
New Hampshire
Another option pull the top cover latch out and clearance the underside a little so the top cover can come up a little more. Keep in mind any of these mods may affect parts interchangeability
 

timo

UZI Talk Supporter
Feedback: 1 / 0 / 0
Joined
Dec 24, 2012
Messages
477
Location
USA
There's a video out there that shows how to properly adjust the cover. I believe Richard Hoffman did it, but not certain
 

MitchWerbellsGhost87

Uzi Talk Life Member, MacExpert!
Feedback: 6 / 0 / 0
Joined
Dec 11, 2022
Messages
1,355
Location
USA
Another option pull the top cover latch out and clearance the underside a little so the top cover can come up a little more. Keep in mind any of these mods may affect parts interchangeability
This is what I did initially, took a cutting disc to the bottom of the latch to try to let it come up a little, but it didn’t solve the problem. I’m gonna try your other suggestions. Thanks man!

ETA.. I did the belt sander to the top of the bolt trick with a Uzi pistol I welded up a while back that was completely locked up by the cover, it worked but I was thinking there had to be an easier, less invasive way to do this. Gonna try bending cover with my press.
 
Last edited:

MitchWerbellsGhost87

Uzi Talk Life Member, MacExpert!
Feedback: 6 / 0 / 0
Joined
Dec 11, 2022
Messages
1,355
Location
USA
There's a video out there that shows how to properly adjust the cover. I believe Richard Hoffman did it, but not certain
I had a feeling he had a good fix for this and when I encountered the problem, I was wishing he was still around to help me!
 

MitchWerbellsGhost87

Uzi Talk Life Member, MacExpert!
Feedback: 6 / 0 / 0
Joined
Dec 11, 2022
Messages
1,355
Location
USA
Update. This is driving me nuts. I have removed as much as I possibly can from the end of the cover, the bottom of the latch and even the front end of the cover where it presses up against the front trunnion stops (it was seemingly tight at THAT end?) I have done everything short of bending the cover in a press, which I’m reluctant to do because it’s an original action arms cover in Mint Condition and the press can be pretty unforgiving..

It has improved to the point where now when the bolt sticks if I point the muzzle towards the ground and jerk my wrist, the bolt will slam home, But it is still sticking… I’m starting to wonder if maybe it is sticking against the blocking bar, as it only seems to stick in the most rearward position when I really yank the handle back HARD.

Is it definitely the top cover that’s causing this problem? What else could potentially be causing this? I’m not sure if I can trim anything else off of that latch or the cover itself.. I may have to bite the bullet and bend the cover slightly but I’m starting to worry that might not be the issue? I would think with everything I removed at this point it would have solved the problem…

 
Last edited:

timo

UZI Talk Supporter
Feedback: 1 / 0 / 0
Joined
Dec 24, 2012
Messages
477
Location
USA
Did you check the gap with a feeler gauge? It seems like you're guessing if it's the gap or not
 

slimshady

Well-known member
Feedback: 0 / 0 / 0
Joined
Sep 19, 2004
Messages
1,478
Get a spray can of dykem and coat the bolt. Get it stuck then carefully remove it. You should be able to see the scraped off coating on the problem area.
 

MitchWerbellsGhost87

Uzi Talk Life Member, MacExpert!
Feedback: 6 / 0 / 0
Joined
Dec 11, 2022
Messages
1,355
Location
USA
Update.. problem solved. I trimmed a little more off the bottom of the top cover latch and it solved the problem.

Thanks guys
 

mistanate

Active member
Feedback: 0 / 0 / 0
Joined
Jul 5, 2023
Messages
40
Location
MA
Glad you got it solved. I was going to recommend trying a completely different top cover to potentially isolate if it was a cover issue or a blocking bar issue. Blocking bar would be a fairly easy test, just cycle with the cover off, but those tolerances are not nearly as tight as the top cover/bolt tolerances. Happy shooting!
 

MitchWerbellsGhost87

Uzi Talk Life Member, MacExpert!
Feedback: 6 / 0 / 0
Joined
Dec 11, 2022
Messages
1,355
Location
USA
Glad you got it solved. I was going to recommend trying a completely different top cover to potentially isolate if it was a cover issue or a blocking bar issue. Blocking bar would be a fairly easy test, just cycle with the cover off, but those tolerances are not nearly as tight as the top cover/bolt tolerances. Happy shooting!
I still suspect the tolerances between the cover the bolt and the blocking bar were the issue as there was no issue until the bolt interfaced with the blocking bar and that’s where it was sticking, it seemed like the bolt was getting squeezed between the cover and the blocking bar. I had to remove a pretty significant chunk from the bottom of the latch to give it enough relief to stop hanging up in that spot. I didn’t think I’d be able to remove that much more from the latch, but I was able to shave off a little more and remedy the issue without rendering the latch useless.


Thanks everyone who chimed in!
 

AKarms

Well-known member
Feedback: 1 / 0 / 0
Joined
Feb 12, 2024
Messages
405
Location
New Hampshire
Is it a mckay bolt wit
I still suspect the tolerances between the cover the bolt and the blocking bar were the issue as there was no issue until the bolt interfaced with the blocking bar and that’s where it was sticking, it seemed like the bolt was getting squeezed between the cover and the blocking bar. I had to remove a pretty significant chunk from the bottom of the latch to give it enough relief to stop hanging up in that spot. I didn’t think I’d be able to remove that much more from the latch, but I was able to shave off a little more and remedy the issue without rendering the latch useless.


Thanks everyone who chimed in!
seems like it was getting squeezed to the blocking bar would be my guess as well. Opening the slot on the bolt might have been the best solution. I’m so used to dealing with mgs I didn’t think to offer that as a solution. If it’s a factory semi bolt with a rounded slot and a squared McKay style blocking bar this is most likely the issue it’s happened to me before
 

MitchWerbellsGhost87

Uzi Talk Life Member, MacExpert!
Feedback: 6 / 0 / 0
Joined
Dec 11, 2022
Messages
1,355
Location
USA
Is it a mckay bolt wit

seems like it was getting squeezed to the blocking bar would be my guess as well. Opening the slot on the bolt might have been the best solution. I’m so used to dealing with mgs I didn’t think to offer that as a solution. If it’s a factory semi bolt with a rounded slot and a squared McKay style blocking bar this is most likely the issue it’s happened to me before
Truth be told this is the first semi auto UZI I have ever built (or owned). I usually only buy/sell SMG parts. I had never messed with a semi auto UZI prior to this besides the semi auto UZI pistol which has no bar (had same issue with the pistol regardless). That said, I wasn’t gonna modify the bolt anyway, because it’s an OEM action arms model B bolt and they are somewhat valuable these days. I have a business on GB selling old MAC and UZI parts etc (I think you have bought some MAC stuff from me if your name is the same on GB as it is here), and at the end of the day, this thing is eventually gonna be parted out and sold down the road like I ultimately do with most of my stuff.. but for now I wanted a semi auto Uzi carbine that I could maybe do a little plinking with here or there. I shaved a tiny bit off the blocking bar and relieved the bottom of the latch a bit more invasively and it seemed to do the trick.

Thanks again for your help.

Oh and yes, the blocking bar is a bit squared off, I’ve never inspected an action arms blocking bar in person, so I can’t comment as to the difference, but I had to do a little bit of reprofiling on the blocking bar to fully remedy the problem.
 

AKarms

Well-known member
Feedback: 1 / 0 / 0
Joined
Feb 12, 2024
Messages
405
Location
New Hampshire
Truth be told this is the first semi auto UZI I have ever built (or owned). I usually only buy/sell SMG parts. I had never messed with a semi auto UZI prior to this besides the semi auto UZI pistol which has no bar (had same issue with the pistol regardless). That said, I wasn’t gonna modify the bolt anyway, because it’s an OEM action arms model B bolt and they are somewhat valuable these days. I have a business on GB selling old MAC and UZI parts etc (I think you have bought some MAC stuff from me if your name is the same on GB as it is here), and at the end of the day, this thing is eventually gonna be parted out and sold down the road like I ultimately do with most of my stuff.. but for now I wanted a semi auto Uzi carbine that I could maybe do a little plinking with here or there. I shaved a tiny bit off the blocking bar and relieved the bottom of the latch a bit more invasively and it seemed to do the trick.

Thanks again for your help.

Oh and yes, the blocking bar is a bit squared off, I’ve never inspected an action arms blocking bar in person, so I can’t comment as to the difference, but I had to do a little bit of reprofiling on the blocking bar to fully remedy the problem.
Yea those squared blocking bars can 100 percent cause that. The outer edges can bind on the rounded action arms slot profile

Yup Thats me on gunbroker
 

Please Visit our Sister Sites Below

Sister Board - Sturmgewehr Sister Board - MachinegunBoards


Please consider becoming an UZI Talk Supporter
Top