Search results

I can’t tell you how many guns I have seen damaged from so called “commercial reloaded” ammo. I include remanufactured ammo in that group. If it’s not factory new or you reloaded it yourself, don’t shoot it. It’s not worth saving a few dollars. Occasionally someone will say they heard of factory...

When buying 115 or 124 grn loaded ammunition look at the manufacturers specs. Not all are loaded the same. PMC and CCI blazer brass are on the low end of the MV/ME spectrum. That’s fine for a modern 9mm pistol but not the UZI. That’s why I almost exclusively buy S&B ammo, it most always on the...

Not to muddy the waters here, but is there a different way thats already in use? For example, most suppressors today have a proprietary type of FH/MB and that’s how they are mounted to the gun. Why not take a FH/MB and permanently attach to a Uzi barrel nut (or threaded barrel). Then you have a...

If you want to shoot anything other than RN bullets, get the machined feed ramp. Well worth the money spent.

Don’t forget to clean out the extractor channel.

I don’t know what the boxes go for every month. However, over time you might end up saving money by purchasing a gun safe. Doesn’t have to be $3000. Costco sometimes has decent prices.

I agree, I just have never gotten into reloading. Maybe I should reconsider.

Couple of the 158gn offerings are RN, why not 147gn. FMJ 115 and 124 are almost always RN, but the 147’s all seem to be some variation of a flat nose. We have been talking about subsonic offering lately, and I was wondering if anyone in the ammo business knows the answer? I would certainly buy them.

I agree, about the almost celebrity status of some gunsmiths. Some deserved and some not. If I and a friend had a bad experience with someone, I might post it too. Nothing wrong with feedback. But, sometimes their status gets them so busy and in a rush to get things done they get careless Or...

The round nose ones work great and are as quiet as your going to get.

I sold an Uzi SMG years back that Vector put in a Semi feed ramp. It ate anything and everything I put in it. It’s a big plus putting Flat nosed subsonic ammo in it and shooting supressed. I am looking for that reliability again.

I am in the process of getting a Semi feed ramp in my SMG. But I was hoping in the interim that I might get better feeding with HP’s. Has anyone done this with any success? I know Barrelxchange says his will feed HP’s. Anyone Had any luck?

Amphibian just threaded and installed a 3 lug adaptor for me on one of my barrels. 1st class work and quick turn around, Highly recommend! The 3 lug cutout on the barrel nut looks factory too. Thanks for the great work !!

It almost looks like the Phosphate gritty texture too.

Sorry no spell check…

There is a matte dark parkerizing grey color and a matte parkerizing grey. Just curious if someone has tried these with the group/vector receivers. How hid it look? Close? I have used the Aluma-Hyde II, just no those colors.

What do you have? Likes, dislikes, recommendations?

Dave, my comments were only my observation, a sample size of one. I was only trying to relate my experiences. Quite frankly, I don’t care if it is slightly out of spec, I only care that it runs And does what I ask of it. If someone is looking for perfection, look elsewhere, maybe an MP5 or the...

My 1st GI Vector UZI did not run out of the box. Sent it back and they put in a modified SA feed ramp. I guess might have been slightly out of spec. It ran 100% after that, even with the .45 kit. They can be corrected, but it can be a pain finding someone good to do it.

There used to be a picatinny rail that would mount to the bayonet lug. It would run back under the handguards the full length. Haven’t seen these in a while. TDI has a small rail that attaches to the bayonet lug. It has enough room to mount something like a Streamlight TLR-1...