Search results

I'll be listing my Galil AR (clone) as a kit soon less receiver, but I will be selling a genuine UA mag adapter with it. I have a good idea on the kit value, but several years ago the adapter was a quite a search, and I can't say I've been able to locate one on recent searches. Just looking...

The Bulgy was the one I was hoping for. I thought I'd ran across a post that seemed to indicate that it had the large diameter stem, I can confirm that the .223 Saiga has the small stem. I always enjoyed my IMI (Action Arms Imports) back in the day when I had them and after quite a few AK...

I'm thinking about revisiting a build I did some years ago with the availability of IMI Galil barrels. I was never happy with the amount of material I had to remove from the bolt lugs to get it to headspace/proper lug contact on the GM barrel on a ORF receiver so for a winters project I may just...

Nothing more fugly than silver and black on a firearm ( ;

The new ATI stocks seem to have a good reputation. Mine has remained tight and fits well at a fraction of the price. I had one of the EARLY SW/Cohair stocks (possibly the one on BMP) and it was on the loose side when extended and I wasn't thrilled with the way the lever asm was made inside...

Member, suka5168 had several made years ago. They were perfect in every respect except some, if not all, were out of spec on the rail (too narrow) and the optics set up for picatinni rail specs wouldn't clamp down. I really felt sorry for the guy and he did everything he could to make things...

Small and simple, hits dead on.

Railed gas tube with a Docter/clone should also work with the factory sights.

Those are along the lines I was thinking. The add ons pictured broke where the handle attached to the carrier, and or, at the 90 degree L. As for the knobs, it was my impression they were silver soldered or brazed, not welded. It's been too many years since I replaced my knob with one from...

See a few threads from time to time on gun boards about makeshift Galil "L" charging handles breaking with responses of metal fatigue but for the life of me I don't recall this being an issue with IMI guns. Have I missed something or is it just poor workmanship on those attempting to copy the...

My 2c-a Golani is a clone...not a Galil and definately not a AK47. That said, it should be able to be made into a fine shooting clone just like many HK clones. The best assessment I've seen thus far is that the bullet guide needs some work so the bullet enters the chamber properly. Some things...

As stated, UA should have it cast into the adapter-most likely Blackthorne as I've seen them on GB for around $99 recently and they have them for sale on their site. MSA's are different in design. If that reference line on the adapter is seated and equally flush along the bottom of the receiver...

Get a steel Galil stock,even a semi beater that has the knuckle attached and locks up tight. APEX has some for around $100. Egun I think it is has/or had new delron covers that fit over the top tube. Disassemble the stock and abrasive blast it with 70 grit aluminum oxide and refinish with flat...

It's screwed and pinned 1/4" or so from the end of the carrier. sand the paint off in that area and see if you can find the pin location (it's pretty much peened in place so it blends with the carrier. Sometimes you can find it by hitting it with cold blue as the pin and carrier take the color...

Same as what's posted above, but I submerge in boiling hot water for 30 sec to a minute. I don't know about the R4, but some of the Galil stocks I've ran across have adheasive on the tubes where they join the knuckle. Try to keep the plastic sleeve out of the water, but this tricks worked...

I don't know if they're any differences, the companies were the importer at the time. In the late 80's I had the a AA ARM .308 and it was good as gold. The only issue I can ever remember having is the flash hider occasionally came loose and a bit of loctite would have easily taken care of that...

FWIW-E-gun/Numerich (sp) does or did have new handguard rivits in stock at one time for anyone interested.

Nathan-no issue here but just so everyone's on the same page, what is the prefered way to contact MSA.

FWIW probably all the Golani have G2 triggers. G2=3 US parts.

If it has the adapter and catch lever, the spring and pin should be nothing to find a suitable replacementat almost any hardware store. (I have two UA adapters and there's nothing special to them). If the price is right, grab it.